{"id":2502,"date":"2026-06-15T16:11:26","date_gmt":"2026-06-15T08:11:26","guid":{"rendered":"https:\/\/www.jcinjectionmolding.com\/?p=2502"},"modified":"2026-09-30T15:59:17","modified_gmt":"2026-09-30T07:59:17","slug":"lcp-celanese-vectra-e130i","status":"publish","type":"material_model","link":"https:\/\/www.jcinjectionmolding.com\/es\/materials\/liquid-crystal-polymer-lcp\/lcp-celanese-vectra-e130i\/","title":{"rendered":"Vectra E130i LCP para moldeo por inyecci\u00f3n personalizado"},"content":{"rendered":"<p><strong>Celanese Vectra E130i<\/strong> is a 30% glass-fiber reinforced liquid crystal polymer (LCP) grade used for precision injection-molded components. The grade&#8217;s published material data can help with an initial selection, but a finished connector or other part must be evaluated against its own drawing, operating conditions and acceptance tests.<\/p>\n<h2>What the manufacturer reports for this grade<\/h2>\n<p>Celanese&#8217;s <a href=\"https:\/\/www.celanese.com\/-\/media\/cewebjssapp\/project\/productdocuments\/lcp\/lcp-026_vectralcpshorttermpropguidetg_am_0613.pdf\">Vectra short-term properties guide<\/a> lists 30% total filler for E130i, a density of 1.61 g\/cm3, tensile stress at break of 150 MPa, tensile modulus of 15,000 MPa, and a heat deflection temperature of 276&deg;C at 1.8 MPa. The guide reports molding shrinkage of 0.1% both parallel and normal to flow under its stated ISO 294-4 method. These are standardized specimen values, not a guarantee for every wall thickness, gate or molded part.<\/p>\n<h2>Where this grade may fit<\/h2>\n<p>Liquid crystal polymers are considered for small, detailed electrical and electronic components where material stiffness, heat response and dimensional behavior matter. The specific part design still determines whether E130i is appropriate. Connector performance also depends on metal contacts, plating, assembly and electrical testing; an LCP material property alone does not establish a connector&#8217;s rating or compliance.<\/p>\n<h2>Tooling and molding checks for an E130i part<\/h2>\n<ul>\n<li><strong>Geometry and fill:<\/strong> identify thin sections, flow length, ribs and gate-sensitive features on the actual design. Do not assume a minimum wall thickness from a generic web claim.<\/li>\n<li><strong>Flow and joining:<\/strong> review potential weld lines at critical features and the likely fiber orientation. Confirm the proposed gate and acceptance tests on the part.<\/li>\n<li><strong>Dimensiones:<\/strong> utilice los datos de contracci\u00f3n del fabricante como referencia inicial y, a continuaci\u00f3n, mida las muestras moldeadas. Registre la direcci\u00f3n del flujo, el acondicionamiento y el m\u00e9todo de medici\u00f3n.<\/li>\n<li><strong>Requisitos t\u00e9rmicos y el\u00e9ctricos:<\/strong> especifique el perfil de exposici\u00f3n real y las pruebas de ensamblaje final. La HDT, el punto de fusi\u00f3n o la medici\u00f3n diel\u00e9ctrica de una resina no constituyen una certificaci\u00f3n del producto terminado.<\/li>\n<\/ul>\n<h2>Solicite moldeo por inyecci\u00f3n personalizado con Vectra E130i<\/h2>\n<p>Para una revisi\u00f3n del proyecto, env\u00ede el modelo 3D y el plano controlado, el grado exacto de resina, la cantidad prevista, las dimensiones cr\u00edticas, los requisitos de rendimiento a nivel de pieza y cualquier norma de herramienta o de ensayo que corresponda. Si se necesita un acabado o un paso de ensamblaje, incl\u00fayalo en el alcance solicitado. Podemos analizar una ruta de utillaje y moldeo para los requisitos documentados e identificar qu\u00e9 debe confirmarse en las muestras. Explore el <a href=\"https:\/\/www.jcinjectionmolding.com\/es\/materials\/liquid-crystal-polymer-lcp\/\">familia de materiales LCP<\/a> o nuestro <a href=\"https:\/\/www.jcinjectionmolding.com\/es\/service\/custom-injection-molding\/\">servicio de moldeo por inyecci\u00f3n personalizado<\/a> para conocer el proceso en general.<\/p>\n<p><em>Nota de la fuente:<\/em> Los valores de propiedades anteriores proceden de una gu\u00eda t\u00e9cnica de Celanese. Antes de la liberaci\u00f3n, consulte la hoja de especificaciones m\u00e1s reciente del grado y acuerde qu\u00e9 resultados de ensayo se aplican al lote suministrado y a la pieza terminada.<\/p>","protected":false},"excerpt":{"rendered":"<p>Celanese Vectra E130i is a 30% glass-fiber reinforced liquid crystal polymer (LCP) grade used for precision injection-molded components. The grade&#8217;s published material data can help with an initial selection, but a finished connector or other part must be evaluated against its own drawing, operating conditions and acceptance tests. What the manufacturer reports for this grade [&hellip;]<\/p>\n","protected":false},"featured_media":2532,"template":"","meta":[],"class_list":["post-2502","material_model","type-material_model","status-publish","has-post-thumbnail","hentry"],"_links":{"self":[{"href":"https:\/\/www.jcinjectionmolding.com\/es\/wp-json\/wp\/v2\/material_model\/2502","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.jcinjectionmolding.com\/es\/wp-json\/wp\/v2\/material_model"}],"about":[{"href":"https:\/\/www.jcinjectionmolding.com\/es\/wp-json\/wp\/v2\/types\/material_model"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.jcinjectionmolding.com\/es\/wp-json\/wp\/v2\/media\/2532"}],"wp:attachment":[{"href":"https:\/\/www.jcinjectionmolding.com\/es\/wp-json\/wp\/v2\/media?parent=2502"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}